Visit Rotoplas Booth 323
IoT for every machine

IoT machine monitoring for every machine on your floor, old or new

Any age. Any brand. One screen.

Yantra24x7 connects CNC machines, injection molding machines, rotomolding ovens, laser cutters, press brakes, die casting cells, welders, robots and older machines with no network port. You see them all on one live screen. Nothing is replaced.

Book a free diagnosticCalculate your ROI
PatentedOur technology is patented
Make in IndiaDesigned and built in India
NASSCOM Deeptech Club I4.0Endorsed deep tech
FANUC IntegratorWorks with FANUC controls
Our promise

Our three promises

Find your hidden machines

Scan the floor and find every machine that was invisible before.

Leave no machine behind

Connect all of them, including legacy equipment, without replacing any.

Stop mistakes at the gate

Check each part before it moves on, so a bad part is caught in your plant, not at your customer.

Works with any brand

Any age. Any brand. One screen.

From a decades-old lathe to the newest robot: Yantra24x7 plugs into each machine in the language it already speaks, and every one of them lands on the same live dashboard. No machine replaced.

Machine types

Which machines can Yantra24x7 connect to?

CNC, injection molding, rotomolding, laser, press brake and die casting. Old and new machines, one platform.

CNC & VMC machine

CNC & VMC

Live status, output and stops for CNC and VMC (vertical machining center) machines, plus part and tool records. Works with FANUC controls.

See how it works for CNC machines
Older machines

How do you connect an old machine with no network port?

Many factories still run machines that are 10 or 30 years old. They have no network port, but they still give off simple signals. A small Yantra24x7 box reads those signals and turns them into live status and cycle counts.

How does the data get from the machine to your phone?

  1. 1
    • Light on when it runs
    • Part counter
    • Electric current

    The machine gives a signal

    Even an old machine gives off simple signals, or data from its control. No network port is needed.

  2. 2
    • Status
    • Cycle count

    The gateway collects it

    The gateway is a small box on the factory floor. It reads the signals and sends them to the dashboard.

  3. 3
    CNC 01Running
    Press 04Idle
    Old latheStopped
    Alert sent to the supervisor
    Example

    The dashboard shows it live

    On your phone, computer and shop-floor TV, with an alert when something needs attention.

The result: an old machine and a new one end up on the same screen. Nothing is replaced.

Connections

Which connection types does Yantra24x7 support?

You do not need to know these names. They are the different ways machines share data, and we pick the right one for each machine.

Every machine speaks its own language. The gateway translates them all, so you see one screen.

Example story. Names and times are illustrative. Footage: stock video.

2:14 AM. A machine stops.Nobody notices. On most floors you find out at the next shift.

Its signal is gibberish. The gateway translates it.Any brand, any age, turned into one clear message.

The cloud stores it safely.Every stop is recorded: when, which machine, and why.

Smart Buddy sends the alert to the right person.On their phone, with a one-tap reply. The machine is back in minutes, not hours.

  1. 1. A machine stopsAt 2:14 AM a machine stops and nobody notices. On most floors you find out at the next shift.
  2. 2. The gateway translatesThe machine's signal is gibberish. The IoT gateway turns any brand and any age into one clear message.
  3. 3. The cloud stores itThe message goes over a secure link and is saved: when, which machine, and why.
  4. 4. Smart Buddy alertsSmart Buddy sends the alert to the right person's phone. They reply with one tap, and the machine is back in minutes, not hours.
Questions

Common questions about connecting machines

Short answers for plant managers.

Can Yantra24x7 connect to old machines?

Yes. If a machine has no network connection, a small box reads simple signals from it, such as on/off signals or a clip-on sensor that senses electric current. That is enough to show when the machine is running, idle or stopped, and to count its cycles, so old machines appear on the same screen as new ones.

Does Yantra24x7 work with FANUC machines?

Yes. Yantra24x7 is a FANUC Integrator and reads data from FANUC controls through FANUC's own data link. It also works with other brands through common standards such as MTConnect, OPC-UA and Modbus, which are simply agreed ways for machines to share their data.

Do I have to change my machine programs?

No. Yantra24x7 only reads signals from the machine. It does not change the machine, its controls or its programs. Your operators keep working the way they do today, and you get a live view of what each machine is doing.

Which types of machines can be monitored?

Yantra24x7 monitors CNC and VMC machines, injection molding machines, rotomolding ovens, laser cutters, press brakes, die casting cells, welding machines, robots and older machines with no network port. If your machine gives off a signal, ask us and we will tell you how to connect it.

Solution

Which of your machines are still invisible?

Book a free diagnostic Try the ROI calculator